Sawblade Sizing
Choose a jeweller’s sawblade to suit the thickness of your material and the detail of the cut. Blade size affects the blade’s dimensions and tooth spacing; the individual product’s sizing table gives the dimensions and tooth density for that range.
Understanding Blade Sizes
The sequence runs from fine /0 sizes through 0 and into larger numbered sizes. Within a blade range, a larger number before /0 means a finer blade: 8/0 is finer than 6/0, 3/0 is finer than 2/0, and 2/0 is finer than 0. Above 0, sizes 1, 2, 3 and upwards become progressively coarser.
From finer to coarser, for example: 8/0, 6/0, 4/0, 3/0, 2/0, 0, 1, 2, 3. Not every range includes every size.
2/0 is often called double zero (00), and 3/0 triple zero (000). Size 0 may also be described as 1/0.
Sawblade Size Table
Sizes are listed from smallest to largest. The table covers our Super Pike Sawblades range. For platinum, white gold and harder metals, see Pike Platinum Sawblades. The Platinum range shares the dimensions and tooth counts shown for sizes 4/0, 3/0, 2/0, 0, 2, 3 and 4; check the category for current availability. Other blade types may differ.
| Size | Thickness x Width (mm) | Teeth per cm | Tooth Pitch (mm) | Minimum Ideal Plate Thickness (mm) |
|---|---|---|---|---|
| 8/0 | 0.32 x 0.16 | 33 | 0.30 | 0.61 |
| 6/0 | 0.36 x 0.18 | 30 | 0.33 | 0.67 |
| 5/0 | 0.40 x 0.20 | 26 | 0.38 | 0.77 |
| 4/0 | 0.44 x 0.22 | 25 | 0.40 | 0.80 |
| 3/0 | 0.48 x 0.24 | 22 | 0.45 | 0.91 |
| 2/0 | 0.52 x 0.26 | 21 | 0.48 | 0.96 |
| 0 | 0.58 x 0.28 | 20 | 0.50 | 1.00 |
| 1 | 0.63 x 0.30 | 19 | 0.53 | 1.06 |
| 2 | 0.70 x 0.34 | 17 | 0.59 | 1.18 |
| 3 | 0.74 x 0.36 | 16 | 0.63 | 1.25 |
| 4 | 0.80 x 0.38 | 15 | 0.67 | 1.34 |
| 5 | 0.85 x 0.40 | 14 | 0.71 | 1.43 |
| 6 | 0.94 x 0.43 | 13 | 0.77 | 1.54 |
Minimum ideal plate thickness is twice the tooth pitch, rounded up to the next 0.01 mm where needed. This is a guide for keeping at least two teeth engaged when the blade is perpendicular to the plate.
Tooth Spacing And Density
Tooth density is the number of teeth along a given length of blade, commonly shown as teeth per centimetre or teeth per inch (TPI). More teeth over the same length means closer spacing; fewer teeth means wider spacing.
Tooth pitch is the distance from one tooth tip to the next. Where density is given in TPI, pitch in millimetres is 25.4 divided by TPI. Check the product table rather than assuming all blade types share identical dimensions for a size.
Matching Teeth To Material Thickness
Choose a tooth spacing that keeps at least two teeth engaged in the material during the cut. Thin sheet needs closely spaced teeth to reduce catching and vibration. Thicker material can accommodate coarser teeth, which provide more room to clear the cuttings.
As a starting check, divide the material thickness by the tooth pitch to estimate how many tooth spacings fit across it. For example, 1 mm material with a 0.4 mm tooth pitch spans about 2.5 tooth spacings. This is an illustration of the relationship, rather than a size recommendation for every material.
Finer blades also suit intricate work and tighter curves. Coarser blades can cut thicker stock more quickly but generally leave a rougher cut. Balance material thickness, the shape being cut and the finish required.
Blade Length And Dimensions
A standard jeweller’s sawblade is approximately 130 mm (5.12 inches) long, with tooth-free ends for the sawframe clamps. Check that the blade suits your frame.
Blade thickness, blade width and tooth spacing are different measurements. Use the dimensions and tooth-density table on the relevant product page when comparing sizes.
Choosing A Blade Type
Standard jeweller’s sawblades suit general piercing and cutting. Harder blade ranges are available for more demanding materials, including platinum and some hard white gold alloys; check the intended applications on the product page.
Very soft materials can clog the spaces between teeth. Skip-tooth blades provide more space for clearing cuttings. Spiral blades cut in multiple directions and can be useful for wax and similar soft materials, although they can be harder to guide along a straight line.